Can you make a special version? I have only 1 Push-Fittings 6mm :(
Von: berni
Am: 8. Januar 2016
No Problem
Hi - I have added a MK8 basis file for those of you who want use a PC4-M6 fitting (a fitting with 6mm thread) instead of the 1/8 fitting. Berni
Von: berni
Am: 8. Januar 2016
Reviews
... Thank you very much for all your efforts. Very nice step by step picture guide.
... Thanks - this extruder has pulled through some 100m of filament without problems.
... Super instructions and rugged design! May be this will probably my favorite :-)
... Looks like you're an adept of the KISS principle (Keep It Simple Stupid). Maybe to also adopt the KIM (Keep It Modular), one could design a modified version to help support flexible filament better after the contact with the bearing to avoid curling. I'll try to do it when I get the opportunity. Also to reduce the dependency on external hardware, I'll integrate some PLA spring like here (http://www.thingiverse.com/thing:704857). Great job and really detailed documentation! Nice. Z Anti-backlash add-on for Prusa i3
... Hello, thanks for all, i have a mendel90 and want to switch to direct drive, open and direct access to filament, and bowden provisionning... but ...
for now, in my Marlin or printer memory i have a 540 m/s for E (filament).
with Direct drive, i suppose i must adapt this value, and i know where to modify it, but it's now depends of MK8 advance and i don't know witch value to set..
Regards Dan
... Love the design. I have been using a airtripper but find it hard to thread at times. This design looks to solve that issue. I am having a hard time finding a source for the 30-40mm spring. Any tips on where you get it?
Von: berni
Am: 8. Januar 2016
Reviews
... Thank you very much for all your efforts. Very nice step by step picture guide.
... Thanks - this extruder has pulled through some 100m of filament without problems.
... Super instructions and rugged design! May be this will probably my favorite :-)
... Looks like you're an adept of the KISS principle (Keep It Simple Stupid). Maybe to also adopt the KIM (Keep It Modular), one could design a modified version to help support flexible filament better after the contact with the bearing to avoid curling. I'll try to do it when I get the opportunity. Also to reduce the dependency on external hardware, I'll integrate some PLA spring like here (http://www.thingiverse.com/thing:704857). Great job and really detailed documentation! Nice. Z Anti-backlash add-on for Prusa i3
... Hello, thanks for all, i have a mendel90 and want to switch to direct drive, open and direct access to filament, and bowden provisionning... but ...
for now, in my Marlin or printer memory i have a 540 m/s for E (filament).
with Direct drive, i suppose i must adapt this value, and i know where to modify it, but it's now depends of MK8 advance and i don't know witch value to set..
Regards Dan
... Love the design. I have been using a airtripper but find it hard to thread at times. This design looks to solve that issue. I am having a hard time finding a source for the 30-40mm spring. Any tips on where you get it?
Von: berni
Am: 8. Januar 2016
Reviews
... Thank you very much for all your efforts. Very nice step by step picture guide.
... Thanks - this extruder has pulled through some 100m of filament without problems.
... Super instructions and rugged design! May be this will probably my favorite :-)
... Looks like you're an adept of the KISS principle (Keep It Simple Stupid). Maybe to also adopt the KIM (Keep It Modular), one could design a modified version to help support flexible filament better after the contact with the bearing to avoid curling. I'll try to do it when I get the opportunity. Also to reduce the dependency on external hardware, I'll integrate some PLA spring like here (http://www.thingiverse.com/thing:704857). Great job and really detailed documentation! Nice. Z Anti-backlash add-on for Prusa i3
... Hello, thanks for all, i have a mendel90 and want to switch to direct drive, open and direct access to filament, and bowden provisionning... but ...
for now, in my Marlin or printer memory i have a 540 m/s for E (filament).
with Direct drive, i suppose i must adapt this value, and i know where to modify it, but it's now depends of MK8 advance and i don't know witch value to set..
Regards Dan
... Love the design. I have been using a airtripper but find it hard to thread at times. This design looks to solve that issue. I am having a hard time finding a source for the 30-40mm spring. Any tips on where you get it?
Push fitting
Can you make a special version?
I have only 1 Push-Fittings 6mm :(
No Problem
Hi -
I have added a MK8 basis file for those of you who want use a PC4-M6 fitting
(a fitting with 6mm thread) instead of the 1/8 fitting.
Berni
Reviews
... Thank you very much for all your efforts. Very nice step by step picture guide.
... Thanks - this extruder has pulled through some 100m of filament without problems.
... Super instructions and rugged design! May be this will probably my favorite :-)
... Looks like you're an adept of the KISS principle (Keep It Simple Stupid). Maybe to also adopt the KIM (Keep It Modular), one could design a modified version to help support flexible filament better after the contact with the bearing to avoid curling. I'll try to do it when I get the opportunity. Also to reduce the dependency on external hardware, I'll integrate some PLA spring like here (http://www.thingiverse.com/thing:704857).
Great job and really detailed documentation! Nice.
Z Anti-backlash add-on for Prusa i3
... Hello,
thanks for all, i have a mendel90 and want to switch to direct drive, open and direct access to filament, and bowden provisionning... but ...
for now, in my Marlin or printer memory i have a 540 m/s for E (filament).
with Direct drive, i suppose i must adapt this value, and i know where to modify it, but it's now depends of MK8 advance and i don't know witch value to set..
Regards
Dan
... Love the design. I have been using a airtripper but find it hard to thread at times. This design looks to solve that issue.
I am having a hard time finding a source for the 30-40mm spring. Any tips on where you get it?
Reviews
... Thank you very much for all your efforts. Very nice step by step picture guide.
... Thanks - this extruder has pulled through some 100m of filament without problems.
... Super instructions and rugged design! May be this will probably my favorite :-)
... Looks like you're an adept of the KISS principle (Keep It Simple Stupid). Maybe to also adopt the KIM (Keep It Modular), one could design a modified version to help support flexible filament better after the contact with the bearing to avoid curling. I'll try to do it when I get the opportunity. Also to reduce the dependency on external hardware, I'll integrate some PLA spring like here (http://www.thingiverse.com/thing:704857).
Great job and really detailed documentation! Nice.
Z Anti-backlash add-on for Prusa i3
... Hello,
thanks for all, i have a mendel90 and want to switch to direct drive, open and direct access to filament, and bowden provisionning... but ...
for now, in my Marlin or printer memory i have a 540 m/s for E (filament).
with Direct drive, i suppose i must adapt this value, and i know where to modify it, but it's now depends of MK8 advance and i don't know witch value to set..
Regards
Dan
... Love the design. I have been using a airtripper but find it hard to thread at times. This design looks to solve that issue.
I am having a hard time finding a source for the 30-40mm spring. Any tips on where you get it?
Reviews
... Thank you very much for all your efforts. Very nice step by step picture guide.
... Thanks - this extruder has pulled through some 100m of filament without problems.
... Super instructions and rugged design! May be this will probably my favorite :-)
... Looks like you're an adept of the KISS principle (Keep It Simple Stupid). Maybe to also adopt the KIM (Keep It Modular), one could design a modified version to help support flexible filament better after the contact with the bearing to avoid curling. I'll try to do it when I get the opportunity. Also to reduce the dependency on external hardware, I'll integrate some PLA spring like here (http://www.thingiverse.com/thing:704857).
Great job and really detailed documentation! Nice.
Z Anti-backlash add-on for Prusa i3
... Hello,
thanks for all, i have a mendel90 and want to switch to direct drive, open and direct access to filament, and bowden provisionning... but ...
for now, in my Marlin or printer memory i have a 540 m/s for E (filament).
with Direct drive, i suppose i must adapt this value, and i know where to modify it, but it's now depends of MK8 advance and i don't know witch value to set..
Regards
Dan
... Love the design. I have been using a airtripper but find it hard to thread at times. This design looks to solve that issue.
I am having a hard time finding a source for the 30-40mm spring. Any tips on where you get it?